FT9xx Development Modules

Based upon Bridgetek’s FT32 high performance, 32 bit RISC core, the FT9xx series provides a plethora of connectivity options, making it the ideal choice for advanced technology bridging solutions. By executing instructions from shadow RAM, rather than flash memory, the FT9xx can operate at true Zero Wait States (0WS) up to 100MHz with 310 DMIPS performance.

In addition, Bridgetek provides a range of modules designed to assist with design and development with the series.

MM900EV Development Modules

The MM900EV development modules provide full hardware feature support for the FT90x MCU in a variety of form factors and feature a connector for accessing external plug-in hardware over an SPI interface. Targeted applications for the module include home security, HMI and automation systems, USB capability products, embedded multimedia applications and a range of other industrial control systems. There are four module types available: the MM900EV1A, which comes without a camera, MM900EV2A with a front-facing CMOS camera; MM900EV3A with a rear-facing CMOS camera and MM900EV-Lite which is optimized for HMI and embedded display applications.

Key Features:

  • FT90x 100-pin QFN package MCU
  • RJ45 with built in magnetics for 10/100Mbps Ethernet transfer
  • Standard USB-A connector to support USB device connection
  • Micro-B USB for connecting to a USB host or providing a power supply over USB
  • In built audio codec for stereo audio output with 3.5mm headphone jack and mono microphone input
  • Debugger interface for FT90x flash programming and EFUSE configuration
  • +5V alternative power supply DC connector
  • 2×5 pins 1.27mm pitch female Micro-Match connector for software download
  • 2×20 pins 2.54mm pitch female header support for external feature expansions
  • 24 pins 0.5mm pitch camera connector and two RGB LEDs (MM900EV2A/3A modules)
  • MicroSD card socket supporting SD3.0 specification
  • 2×8 pins 2.54mm pitch dual entry female header and 16 pins 0.5mm pitch FFC/FPC connectors for SPI master to support LCD display modules
  • MM900EVxA Datasheet
  • MM900EV-LITE Datasheet


MM930Mini Module

The MM930Mini Module is a USB microcontroller development module in the Bridgetek product range. It utilizes the FT930Q bridge chip which can handle all USB signalling and protocols. It is ideal for development purposes to quickly prove functionality of adding USB to a target design.

Key Features:

  • USB 2.0 Hi-Speed compatible.
  • Reduced development time
  • Rapid integration into existing systems
  • USB powered – no external power supply needed
  • Based on the USB Hi-Speed FT930Q device
  • Entire USB protocol handled by D2xx hardware engine
  • USB micro-B connector common on many commercial devices
  • On-board 500mA 3.3V LDO regulator, 12MHz crystal, 32kHz crystal
  • Asynchronous Serial data transfer rates from 300 baud to 12 Mbaud at TTL levels
  • One SPI master supports single / dual / quad modes of data transfer. Clock rate is up to 25 MHz
  • One SPI slave support single data transfer with 25MHz clock
  • I2C bus interface can be configured as master or slave, with data transfers up to 3.4Mbps
  • UHCI / OHCI / EHCI host controller compatible
  • One SPI slave support single data transfer with 25MHz clock
  • MM930Mini Module Datasheet


The UMFTPD2A debugger/programmer module provides a USB bridge between the FT9xx Eclipse IDE development tools runnng on a PC and the FT9xx 1-wire debug pin. This module can be used to program, configure the EFUSE and debug firmware running on the FT9xx series.

Key Features:

  • Hi-Speed USB to one-wire interface converter
  • Hi-Speed USB to MPSSE interface converter
  • Hi-Speed USB to UART interface converter
  • Provides H/W Reset# signal
  • Provides multiple generic GPIO control signals
  • PWREN# line to control +5 power supply
  • Fuse protected with 0.5A hold current and schottky diode on the output power line
  • Two dedicated GPIOs to control VPP and FRSC power supplies
  • Three LEDs for power supply indication
  • 2X5 way 1.27mm pitch Micor-MaTch socket
  • 2X6 way 2.54mm pitch through hole pin header
  • Micro-B type USB port
  • Micro-MaTch Male to Male 10 pin ribbon cable

There is an FTDI FT4232H chip on the UMFTPD2A module and the FT4232H datasheet is available here.
Please install the VCP and D2XX driver by the setup executable and it is available here.


FT90x Series Toolchain

Click here to download the FT90x Series Toolchain to enable code development and debug for the FT90x series Development Modules.